How To Un Solder Copper Pipe

There are a few ways to unsolder copper pipe. One way is to use a propane torch. Turn on the torch and heat the solder joint until the solder liquefies. Then use a screwdriver or pliers to gently pull the pipe away from the solder joint. Another way to unsolder copper pipe is to use a soldering iron. Place the soldering iron on the solder joint and wait until the solder liquefies. Then use pliers to gently

How To Un Solder Copper Pipe

There are a few ways to unsolder copper pipe. One is to use a torch. Heat the area around the solder joint until the solder liquefies. Then use a plunger or a screwdriver to push the solder out of the joint. Another way is to use a desoldering pump. Put the pump over the solder joint and squeeze the handle. The solder will be sucked into the pump.

-copper pipe -solder – flux -soldering iron -tin snips

  • Apply flux to the copper pipe and solder hold the soldering iron against the
  • Use a soldering iron to heat the copper pipe until the solder melts
  • Use a wire brush to clean the oxidation off the copper pipe

-How to un solder copper pipe: -Clean the area around the joint to be unsoldered – Apply flux to the joint and heat it with a torch until the solder liquefies – Use a soldering iron to remove the rest of the solder from the joint


Frequently Asked Questions

How Do You Remove Solder From A Pipe?

You can remove solder from a pipe using a wire brush.

How Do You Remove Solder Without A Torch?

There are a few ways to remove solder without a torch. One way is to use a desoldering pump. Another way is to use solder wick.

Can You Desolder Pipes?

Yes, you can desolder pipes. You can use a variety of methods, such as a soldering iron, solder wick, or solder sucker.

Can You Un Solder A Pipe?

Yes, depending on the type of solder used, it is possible to unsolder a pipe. By using a heat gun and a solder sucker, the solder can be melted and removed from the pipe.

How Do You Remove Old Solder From Brass?

There are a few ways to remove old solder from brass. One way is to use a flux pen to remove the flux residue, and then use a brass brush to remove the solder. Another way is to use a soldering iron and a solder sucker to remove the solder.

How Do You Remove Solder Easily?

There are a few ways to remove solder easily. One way is to use a solder sucker, which is a small hand-held pump that uses vacuum to suck up the solder. Another way is to use a desoldering braid, which is a thin copper wire mesh that is used to soak up the solder.

Can You Remove Soldered Pipe?

Yes, you can remove a soldered pipe by heating the solder until it liquefies and then using a plunger to clear the obstruction.

How Do You Remove Solder Without Wick Or Flux?

Some people use a solder sucker to remove solder without wick or flux.

How Do You Remove Old Solder That Won’T Melt?

If the solder is not budging, then you might need to apply more heat. Try using a higher-wattage soldering iron, or if you’re using a torch, hold the flame closer to the solder joint. If the old solder is still refusing to melt, you might need to use a solder remover or desoldering braid to remove it.

Can Solder Be Removed From Copper Pipe?

Yes, solder can be removed from copper pipe using a flux and a torch. The flux will help to break down the solder, and the torch will heat the copper pipe until the solder liquefies and can be wiped away.


To Summarize

Unsoldering copper pipe is a relatively straightforward process, although there are a few tricks to it that can make the job easier. First, use a utility knife or wire cutters to cut the solder joint apart. Next, use a propane torch to heat the copper pipe until the solder begins to melt. Finally, use a pair of pliers to twist the pipe and remove the melted solder.

Leave a Comment

Your email address will not be published.